EXTRACTED TEXT FROM: 810+479+534+A561+A555+P09-5-headed wind tornado.docx

Please read the manual carefully before installing and using the productPlease read the manual carefully before installing and using the productUser Manual810+479+534+A561+A555+P09-5-headed wind tornadoUser Manual810+479+534+A561+A555+P09-5-headed wind tornado                                                
Please read the manual carefully before installing and using the product
Please read the manual carefully before installing and using the product
User Manual
810+479+534+A561+A555+P09-5-headed wind tornado
User Manual
810+479+534+A561+A555+P09-5-headed wind tornado

















directory

1. Precautions and installation precautions and installation3
1.1 Statement3
1.2 Maintenance3
1.3 Product precautions3
1.4 Product introduction4
2. Display panel and key definitions4
2.1 Control panel4
2.2 Menu function5
3. Master-slave control7
4. DMX512 control7
4.1 Address Code7
4.2 CH26 Channel Table8
4.3 CH75 Channel Table9
5. Common faults12

1. Precautions and installation precautions and installation
1.1 Statement
Thank you for choosing our products! This product leaves the factory with good performance and complete packaging. In order for you to use this product safely and effectively, please read this instruction manual carefully and completely before using this product. This manual contains important information for installation and use, please follow the requirements of the manual for installation and operation, and at the same time, please keep this manual properly for use at any time.
This manual is subject to technical changes without notice.
1.2 Maintenance
This fixture is intended for professional use only.
If the external flexible cable or wire of this luminaire is damaged, it should be replaced with a special wire or wire provided by the manufacturer or its service agent.
The light source contained in this luminaire may only be replaced by the manufacturer or its service agent or similar qualified personnel.
Always connect the product to a protected circuit (circuit breaker or fuse). Ensure that the product has proper electrical grounding to avoid the risk of electric shock or fire.
To avoid unnecessary wear and extend its life, when not in use, the power supply should be completely cut off by circuit breaker or unplugged.
The housing may heat up while the product is running. This product should be installed in a well-ventilated location.
When the product is transferred from an extreme temperature environment (e.g., from a cold truck to a warm and humid environment), the internal electronics of the product can condense. To avoid malfunctions, allow the product to adapt to its surroundings before turning on the power.
Flash is known to trigger seizures. Users must comply with local notification laws regarding flash use.
1.3 Product precautions
Disconnect the power supply before cleaning the product or replacing the fuse.
When not in use, replace and secure all power, data, USB, or other port shields to IP protection. 
Use a safety rope when attaching this product above your head.
Connect this product to a grounded and protected circuit.
When the product is on, look at the light source.
Do not place any flammable materials within 20  cm of this product when operating or turning on the power  supply. 
Do not operate this product if the housing, lenses, or cables are damaged.
This product can only be handled using handles or hoisting/mounting brackets. 
To avoid unnecessary wear and extend its life, when not in use, the power supply should be completely cut off by circuit breaker or unplugged.
In case of serious operating problems, it should be stopped immediately






1.4 Product introduction
Voltage: DC 24+12V
Power: 324W
Lamp beads: 5pcs 6065 4-in-1 RGBW + 18pcs 5050 colorful 3-in-1 RGB light strip*5
Control mode: DMX512, self-propelled, voice controlled, with RDM function
Channels: CH26, CH75
Dimming: 32bit 0~100% linear dimming
Features: Electrodeless + auxiliary light + beam
Working temperature: -30°C~50°C
Strobe frequency: 1~30HZ
Appearance: Metallic, black
Connection: DMX512 input/output / power input/output.
IP Rating: IP20
Size:                                
Weight: 

2. Display panel and key definitions
2.1 Control panel




Menu key: enter/return to the main menu
Up key: The menu function selects up/adds parameters
Down key: Menu function selects down/decrements parameters
Confirm key: Select the menu function, and confirm and save it when the menu function parameters are modified.


2.2 Menu function
After powering on and resetting the whole machine, press the menu button to enter the main menu (the main menu interface exits after 30 seconds of no operation), see the main menu menu (a total of 5 main menu options) for details; Select the main menu with the up or down button, click the confirmation button to modify the function parameters of each menu, and then press the confirmation button to save the current function parameters (with power loss memory after saving). 

Main menu
Submenu
Menu function description
1. System settings
1. DMX address
Modify the DMX address code up or down (the address code can be selected in the range 001-512), and confirm that the key is saved, default 001.

2. X reversal
Modify X up/down to turn on/off, confirm key to save, and turn off by default.

3. Y reversal
Modify Y upwards or downwards to turn on/off, confirm the key to save, and turn off by default.

4. No signal
Modify the signal clear/hold up or down, confirm the key to save, and clear the default.

5. Voice control sensitivity
Modify up or down (range 000-099), make sure the key is saved, default 009.

6. Temperature-fan
Modify Auto/Standard/Quiet up or down, make sure key save, default auto.

7. Dimming curve
Modify the linear curve, square rate curve, inverse square rate curve, and S curve up or down, and confirm that the key is saved, and the default linear curve is the default.

8. Dimming curve
Modify up or down fast/smooth, confirm key save, fast by default.

9. ID number
Modify up or up to close /Y1-Y5, confirm the key to save, and close by default.

10. Reset
Modify yes/no up or up, confirm key save, default no.

11. Restore factory settings
Modify yes/no up or up, confirm key save, default no.

12. Advanced settings

2. Operation mode
1. Operation mode
Select the running mode up or down, DMX/Voice Control/Auto, confirm the key to save, default DMX.

2. Channel selection
Select channel CH26, CH75 up or down, confirm key to save, default CH26.
3. Manual control

1. X-axis
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

2. X-axis fine-tuning
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

3. X-axis speed
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

4. X-axis macro function
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

5. Y-axis
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

6. Fine-tuning the Y-axis
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

7. Y-axis speed
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

8. Y-axis macro function
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

9. The X-axis is infinite
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

10. Dimming
Modify up or down (adjustable range 000-255), confirm the key to save, default 255.

11. The main light is flashing
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

12. Halo strobe
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

13. Red
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

14. Green
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

15. Blue
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

16. White
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

17. Color temperature
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

18. Color macro
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

19. Halo red
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

20. Halo green
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

21. Halo blue
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

22. Main light mode
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

23. Main light mode speed
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

24. Halo mode
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

25. Halo mode speed
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.

26. Function
Modify up or down (adjustable range 000-255), confirm the key to save, default 000.
4. Display settings
1. Language selection
Select Chinese/EN (English) up or down, confirm the key to save, default Chinese.

2. Inverted settings
Select Turn off/on the display setting up or down, confirm that the key is saved, and turn off by default.

3. Screensaver settings
Select Turn off/on backlight settings up or down, confirm the key to save, and turn on by default.

4. Software version
M5RF
5. Information settings
sensor
Used to view Hall status and temperature communication status

error message
Used to display error messages 

Channel information
Used to display DMX channel data 

Time information
Light on time
Luminaire time
6. Factory setting
Show Please enter your password! Modify it up or down to 138, and then press the confirm button to enter the factory settings.
1. X1 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


2. Y1 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


3. F1 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


4. X2 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


5. Y2 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


6. F2 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


7. X3 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


8. Y3 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


9. F3 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


10. X4 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


11. Y4 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


12. F4 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


13. X5 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


14. Y5 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


15. F5 axis calibration
Modify up or down (range 000-255), confirm key save, default 128.


16. X itinerary
Modify up or down (range 000-255), confirm key save, default 128.


17. Y itinerary
Modify up or down (range 000-255), confirm key save, default 128.


18. Open value
Modify up or down (range 000-255), confirm the key saves, default 180.


19. Red
Modify up or down (range 032-255), confirm key save, default 255.


20. Green
Modify up or down (range 032-255), confirm key save, default 255.


21. Blue
Modify up or down (range 032-255), confirm key save, default 255.


22. White
Modify up or down (range 032-255), confirm key save, default 255.


23. Red 1
Modify up or down (range 032-255), confirm the key to save, default 252.


24. Green 1
Modify up or down (range 032-255), confirm the key to save, default 252.


25. Blue 1
Modify up or down (range 032-255), confirm the key to save, default 252.


26. White 1
Modify up or down (range 032-255), confirm the key to save, default 252.


27. Red 2
Modify up or down (range 032-255), confirm the key to save, default 252.


28. Green 2
Modify up or down (range 032-255), confirm the key to save, default 252.


29. Blue 2
Modify up or down (range 032-255), confirm the key to save, default 252.


30. White 2
Modify up or down (range 032-255), confirm the key to save, default 252.


31. Red 3
Modify up or down (range 032-255), confirm the key to save, default 252.


32. Green 3
Modify up or down (range 032-255), confirm the key to save, default 252.


33. Blue 3
Modify up or down (range 032-255), confirm the key to save, default 252.


34. White 3
Modify up or down (range 032-255), confirm the key to save, default 252.


35. Red 4
Modify up or down (range 032-255), confirm the key to save, default 252.


36. Green 4
Modify up or down (range 032-255), confirm the key to save, default 252.


37. Blue 4
Modify up or down (range 032-255), confirm the key to save, default 252.


38. White 4
Modify up or down (range 032-255), confirm the key to save, default 252.


39. Red 5
Modify up or down (range 032-255), confirm the key to save, default 252.


40. Green 5
Modify up or down (range 032-255), confirm the key to save, default 252.


41. Blue 5
Modify up or down (range 032-255), confirm the key to save, default 252.


42. White 5
Modify up or down (range 032-255), confirm the key to save, default 252.


43. Current
Modify up or down (range 032-255), confirm the key to save, default 240.


44. Temperature
Modify the temperature parameter (range 40-65) up or down, confirm the key to save, default 060.


45、LED
Modify LEDA/LEDB up or down, make sure the key is saved, and the default LEDA is the default.


46. LEDXYF direction
Modify up or down (range 000-255), confirm the key saves, default 000.


47、Logo
Select 000/001 up or down, confirm the key to save, default 000.


48. Synchronous update
Select On/Off up or down, confirm to save, and turn off by default.


49. Time is cleared
Select Yes/No up or down, confirm the key saves, no by default.
3. Master-slave control
    There are 2 or more identical lamps connected with DMX three-core signal cables, all lamps are modified to 001~512 arbitrary address code, any one is set as the host, other lamps are slaves, and all slave displays do not flicker; When the main unit is used to adjust the gradient, pulse change, jump, voice control, and self-propelled effects, all slave synchronized gradients, pulse changes, jumps, voice-controlled, and auto-propelled effects.
Special attention: 1. A group of lamps can only set one host, if there are multiple hosts, all the lamps will flash randomly and not synchronized.
All luminaires must be active when the DMX512 console is turned off.
4. DMX512 control
4.1 Address Code
All the lamps are set with the address code, connect all the lamps to the DMX512 console in parallel with DMX three-core signal cables, the address code stops flashing, indicating that the DMX512 console signal has been sent to the lamp, and use the DMX512 console to control the relevant functions according to the channel instructions.
4.2 CH26 Channel Table
passage
Channel value
Basic features:
1
000-255
X-axis    
2
000-255
X-axis fine-tuning 
3
000-255
X-axis speed  
4
000-255
X-axis macro function 
5
000-255
Y-axis        
6
000-255
Y-axis fine-tuning
7
000-255
Y-axis velocity  
8
000-255
Y-axis macro function
9
000-255
The X-axis is infinite  
10
000-255
Dimming     
11
000-255
The main light is flashing
12
000-255
Halo strobe  
13
000-255
red     
14
000-255
green    
15
000-255
blue     
16
000-255
white     
17
000-255
Temperature    
18
000-255
Color macro     
19
000-255
The halo is red  
20
000-255
Halo green 
21
000-255
Halo blue
22
000-255
Main light mode 
23
000-255
Main light mode speed
24
000-255
Halo mode  
25
000-255
Halo mode speed
26
000-255
Function
4.3 CH75 Channel Table
passage
Channel value
Basic features:
1
000-255
Total dimming
2
000-255
The main light is flashing
3
000-255
Halo strobe
4
000-255
X-axis 1 
5
000-255
X-axis 1 fine-tuning 
6
000-255
X-axis 1 infinite
7
000-255
Y-axis 1 
8
000-255
Y-axis 1 fine-tuning 
9
000-255
Red 1     
10
000-255
Green 1    
11
000-255
Blue 1     
12
000-255
White 1    
13
000-255
Halo 1 red
14
000-255
Halo 1 green 
15
000-255
Aura 1 blue
16
000-255
Halo 1 mode  
17
000-255
Halo 1 mode speed
18
000-255
X-axis 2
19
000-255
X-axis 2 fine-tuning
20
000-255
X-axis 2 infinite
21
000-255
Y-axis 2
22
000-255
Y-axis 2 fine-tuning
23
000-255
Red 2
24
000-255
Green 2
25
000-255
Blue 2
26
000-255
White 2
27
000-255
Halo 2 red
28
000-255
Halo 2 green
29
000-255
Halo 2 blue
30
000-255
Halo 2 mode
31
000-255
Halo 2 mode speed
32
000-255
X-axis 3
33
000-255
X-axis 3 fine-tuning
34
000-255
X-axis 3 infinite
35
000-255
Y-axis 3
36
000-255
Y-axis 3 fine-tuning
37
000-255
Red 3
38
000-255
Green 3
39
000-255
Blue 3
40
000-255
White 3
41
000-255
Halo 3 red
42
000-255
Halo 3 green
43
000-255
Halo 3 blue
44
000-255
Halo 3 mode
45
000-255
Halo 3 mode speed
46
000-255
X-axis 4
47
000-255
X-axis 4 fine-tuning
48
000-255
X-axis 4 infinite
49
000-255
Y-axis 4
50
000-255
Y-axis 4 fine-tuning
51
000-255
Red 4
52
000-255
Green 4
53
000-255
Blue 4
54
000-255
White 4
55
000-255
Halo 4 red
56
000-255
Halo 4 green
57
000-255
Halo 4 blue
58
000-255
Halo 4 mode
59
000-255
Halo 4 mode speed
60
000-255
X-axis 5
61
000-255
X-axis 5 fine-tuning
62
000-255
X-axis 5 infinite
63
000-255
Y-axis 5
64
000-255
Y-axis 5 fine-tuning
65
000-255
Red 5
66
000-255
Green 5
67
000-255
Blue 5
68
000-255
White 5
69
000-255
Halo 5 red
70
000-255
Halo 5 green
71
000-255
Halo 5 blue
72
000-255
Halo 5 mode
73
000-255
Halo 5 mode speed
74
000-255
XY axis speed  
75
000-255
Function
Function
Channel value
Function description:
000--005
No function
006--007
No function
008--009
No function
010--029
No function
030--039
Dimming curve: linear
040--049
Dimming curve: square rate
050--059
Dimming curve: antisquare rate
060--069
Dimming curve: S-curve
070--079
Temperature-Fan Mode: Automatic
080--089
Temperature-Fan Mode: Standard
090--099
Temperature-Fan Mode: Quiet
100--109
No function
110--119
No function
120--122
No function
123
No function
124
No function
125
No function
126
No function
127
No function
128
No function
129
No function
130
No function
131
No function
132
No function
133
No function
134
No function
135
No function
136
No function
137
No function
138--139
No function
140--149
X-axis reset
150--159
Head reset 
160--169
Head reversed: Yes
170--179
Head reverse: No
180--199
No function
200--209
All reset
210--219
Dimming speed: fast
220--229
Dimming speed: smooth
230--255
No function



5. Common faults
For some common faults, corresponding solutions are proposed. Any unresolved issues should be handled by professionals. Before maintaining the lamp, disconnect the power supply.
The lamp beads don't turn on
Check whether the voltage matching the lamp is installed;
Check whether the power supply connection or control switch of the lamp is in poor contact;
Check whether the power supply is insufficient;
Check if the DMX512 controller has sent instructions.
2. The lamp does not accept the control of the console after normal reset
Check whether the numeric start address value and function options of the luminaire are correct;
Check whether the connection of the communication control line is correct, the communication line is too long or has been interrupted;
Check whether the control equipment is failing, and check whether the signal amplifier connected in series is failing;
Check whether the communication line is too long or if other devices interfere with each other;
Optimize the wiring, shorten the length of the control signal line, and separate the high-voltage and low-voltage lines.
Add a signal amplifier;
The signal line adopts high-quality shielded twisted pair wire;
Connect the signal termination resistor (120 ohms) at the end of the luminaire.
3. The light fixture cannot be started
Check whether the power supply parameters are consistent with the lamps;
Check that the lamps are in poor contact or fall off due to extrusion deformation, internal parts vibration, moisture, etc. during long-distance transportation.
Check whether the wires and connectors inside the lamp are falling off or loose.
Check the electronic components of the lamp (such as electronic transformers, PCB boards, motor control boards, etc.) for looseness, short circuits, and burnouts.
